Fine particles production in sand under triaxial compression
Abstract
An experimental study, carried out in laboratory using a triaxial apparatus, proposes to evaluate the influence of grain size, grain shape and confining stress in fine particles production in sand specimen subjected to triaxial loading. 16 triaxial tests were conducted on specimens of an initial density index of 0.90 using the pluviation technique, with three different sands and under initial confining pressure of 100, 400, 800 and 1200 kPa. The experimental results show that the fine particles production is considerably affected by confining stresses, even at low values (100 kPa), and also by grain geometry. The experimental results show also that the fine particles production increase with the strain level during the shearing test.References
Al-Abduwani, F. A. H., A. Shirzadi, W. M. G. T. van den Broek, P. K. Currie (2005) Formation damage vs. solid particles deposition profile during laboratory-simulated PWRI. Society of petroleum engineers journal 10(2): 138–151.
ASTM D 4253 (2006) Standard test methods for maximum index density and unit weight of soils using a vibratory table.
Benahmed, N. (2001) Comportement mécanique d’un sable sous cisaillement monotone et cyclique: application aux phénomènes de liquéfaction et de mobilité cyclique. Thèse de doctorat, Ecole Nationale des Ponts et Chaussées, Marne-la-Vallée, France.
Benahmed, N., J. Canou, J. C. Dupla (2004) Structure initiale et proprietes de liquefaction statique d’un sable. Comptes rendus mécanique 332(11): 887-894.
Chuhan, F.A., A. Kjeldstad, K. Bjørlykke, K. Høeg (2002) Porosity loss in Sand by Grain Crushing—Experimental Evidence and Relevance to Reservoir Quality. Marine and Petroleum Geology 19(1): 39-53.
Crawford, B. R., M. J. Gooch, D. W. Webb (2004) Textural controls on constitutive behavior in unconsolidated sands: micromechanics and cap plasticity. Proceedings of 6th Int. Conf. North American Rock Mechanics Symposium (NARMS). American Rock Mechanics Association, ARMA/NARMS 04-611
Dadda, A., S. Feia, S. Ghabezloo, J. Sulem (2015) Fraturation des grains et l’évolution de la micro-structure d’un sable sous fortes contraintes. CongrésAlgérien de Mécanique (CAM 2015), El Oued 25-27 Octobre 2015.
Farajzadeh, R. (2004) Produced water re-injection (pwri) an experimental investigation into internal filtration and external cake build up. Thesis, Faculty of Civil Engineering and Geosciences, Delft University of Technology.
Feda, J. (2002) Notes on the effect of grain crushing on the granular soil behaviour. Engineering Geology 63(1-2): 93-98.
Feia, S., J. Sulem, J. Canou, S. Ghabezloo, X. Clain (2016) Changes in permeability of sand during triaxial loading: effect of fine particles production. Acta Geotechnica 11(1): 1-19.
Feia, S., S. Ghabezloo, J. F. Bruchon, J. Sulem, J. Canou, J. F. Dupla (2014) Experimental evaluation of the pore-access size distribution of sands. Geotechnical Testing Journal 37(4): 1-8.
Hardin, B. O. (1985) Crushing of soil particles. Journal of geotechnical Engineering 111(10): 1177-1192.
Hazen, A. (1911) Discussion of ‘Dams on sand foundations’ by A. C. Koenig. Transactions of the American Society of Civil Engineers 73: 199-203.
Kolbuszewski, J. J. (1948) An experimental study of the maximum and minimum porosities of sands. 2nd International Conference Soil Mechanics Foundation Engineering, volume 1, Rotterdam.
Lade, P. V. & J. A. Yamamuro (1996) Undrained sand behavior in axisymmetric tests at high pressures. Journal of Geotechnical Engineering 122(2): 120-129.
Lee, K. L., I. Farhoomand (1967) Compressiblity and crushing of granular soil in anisotropic triaxial compression. Canadian Geotechnical Journal, 4(1): 68-86.
Levacher, D., J. Garnier, P. Chambon (1994) Reconstitution d’éprouvettes de sable: appareil de pluviation. Revue française de la géotechnique (68):49-56.
Li, Z., R. C. K. Wong (2008) Estimation of suspended particle retention rate and permeability damage in sandstone from back analysis of laboratory injection tests. Proceedings of canadian international petroleum conference. Society of Petroleum Engineers.
Miura, S., S. Toki (1982) A sample preparation method and its effect on static and cyclic deformationstrength properties of sand. Soils and Foundations 22(1): 61-77.
Nguyen, V.H. (2012) Compaction des roches réservoirs peu ou non consolidées: impacts sur les propriétés de transport. Thèse de doctorat, Université de Cergy-Pontoise.
Rad, N.S., M.T. Tumay (1987) Factors affecting sand specimen preparation by raining. ASTM Geotechnical Testing Journal 10(1): 31-57.
Vaid, Y.P., D. Negussey (1984) Relative density of air and water pluviated sand. Soils and Foundations 4(2): 101-105.
ASTM D 4253 (2006) Standard test methods for maximum index density and unit weight of soils using a vibratory table.
Benahmed, N. (2001) Comportement mécanique d’un sable sous cisaillement monotone et cyclique: application aux phénomènes de liquéfaction et de mobilité cyclique. Thèse de doctorat, Ecole Nationale des Ponts et Chaussées, Marne-la-Vallée, France.
Benahmed, N., J. Canou, J. C. Dupla (2004) Structure initiale et proprietes de liquefaction statique d’un sable. Comptes rendus mécanique 332(11): 887-894.
Chuhan, F.A., A. Kjeldstad, K. Bjørlykke, K. Høeg (2002) Porosity loss in Sand by Grain Crushing—Experimental Evidence and Relevance to Reservoir Quality. Marine and Petroleum Geology 19(1): 39-53.
Crawford, B. R., M. J. Gooch, D. W. Webb (2004) Textural controls on constitutive behavior in unconsolidated sands: micromechanics and cap plasticity. Proceedings of 6th Int. Conf. North American Rock Mechanics Symposium (NARMS). American Rock Mechanics Association, ARMA/NARMS 04-611
Dadda, A., S. Feia, S. Ghabezloo, J. Sulem (2015) Fraturation des grains et l’évolution de la micro-structure d’un sable sous fortes contraintes. CongrésAlgérien de Mécanique (CAM 2015), El Oued 25-27 Octobre 2015.
Farajzadeh, R. (2004) Produced water re-injection (pwri) an experimental investigation into internal filtration and external cake build up. Thesis, Faculty of Civil Engineering and Geosciences, Delft University of Technology.
Feda, J. (2002) Notes on the effect of grain crushing on the granular soil behaviour. Engineering Geology 63(1-2): 93-98.
Feia, S., J. Sulem, J. Canou, S. Ghabezloo, X. Clain (2016) Changes in permeability of sand during triaxial loading: effect of fine particles production. Acta Geotechnica 11(1): 1-19.
Feia, S., S. Ghabezloo, J. F. Bruchon, J. Sulem, J. Canou, J. F. Dupla (2014) Experimental evaluation of the pore-access size distribution of sands. Geotechnical Testing Journal 37(4): 1-8.
Hardin, B. O. (1985) Crushing of soil particles. Journal of geotechnical Engineering 111(10): 1177-1192.
Hazen, A. (1911) Discussion of ‘Dams on sand foundations’ by A. C. Koenig. Transactions of the American Society of Civil Engineers 73: 199-203.
Kolbuszewski, J. J. (1948) An experimental study of the maximum and minimum porosities of sands. 2nd International Conference Soil Mechanics Foundation Engineering, volume 1, Rotterdam.
Lade, P. V. & J. A. Yamamuro (1996) Undrained sand behavior in axisymmetric tests at high pressures. Journal of Geotechnical Engineering 122(2): 120-129.
Lee, K. L., I. Farhoomand (1967) Compressiblity and crushing of granular soil in anisotropic triaxial compression. Canadian Geotechnical Journal, 4(1): 68-86.
Levacher, D., J. Garnier, P. Chambon (1994) Reconstitution d’éprouvettes de sable: appareil de pluviation. Revue française de la géotechnique (68):49-56.
Li, Z., R. C. K. Wong (2008) Estimation of suspended particle retention rate and permeability damage in sandstone from back analysis of laboratory injection tests. Proceedings of canadian international petroleum conference. Society of Petroleum Engineers.
Miura, S., S. Toki (1982) A sample preparation method and its effect on static and cyclic deformationstrength properties of sand. Soils and Foundations 22(1): 61-77.
Nguyen, V.H. (2012) Compaction des roches réservoirs peu ou non consolidées: impacts sur les propriétés de transport. Thèse de doctorat, Université de Cergy-Pontoise.
Rad, N.S., M.T. Tumay (1987) Factors affecting sand specimen preparation by raining. ASTM Geotechnical Testing Journal 10(1): 31-57.
Vaid, Y.P., D. Negussey (1984) Relative density of air and water pluviated sand. Soils and Foundations 4(2): 101-105.
Published
2016-12-24
How to Cite
FEIA, Sadok et al.
Fine particles production in sand under triaxial compression.
Journal of Applied Engineering Science & Technology, [S.l.], v. 3, n. 1, p. 1-6, dec. 2016.
ISSN 2571-9815.
Available at: <http://univ-biskra.dz/revues/index.php/jaest/article/view/1894>. Date accessed: 27 dec. 2024.
Issue
Section
Section C: Geotechnical and Civil Engineering
Keywords
Triaxial test; Granular materials; Grain breakage; Fine particles
J. Appl. Eng. Sci. Technol. (JAEST - ISSN 2352-9873) is a peer-reviewed quarterly journal dedicated to the applied engineering sciences and technology. The JAEST provides immediate open access to its content on the principle that making research freely available to the public supports a greater global exchange of knowledge.
There is no submission or publication fee for papers published in the JAEST.
Authors who publish in the JAEST agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in the JAEST.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in the JAEST.
- Authors are permitted to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access). Any such posting made before acceptance and publication of the Work shall be updated upon publication to include a reference to the JAEST and a link to the online abstract for the final published Work in the Journal.
